Furnace Repair and Servicing

April 23, 2016

Furnace Repair Service

Before you decide to call a repairer to fix your furnace you should, first of all, try to find out what the problem is and decide whether you can be able to fix the furnace yourself or not.

Seeking a qualified contractor repair in Kalamazoo is a good idea, but what most people do not realize is that you can try to fix the problem on your own. AboutFurnace Repair by ecobuilthvac.com twenty percent to thirty percent of all the calls made to a repairer are not necessary because these professionals are called for minor issues that can be fixed easily.

Preventative Measures

There are certain measures you can take to ensure that the cooling system or the heating system is working properly and therefore, it would be unnecessary to call for a repairman in Kalamazoo Michigan.

1 Examine The Filter.

First you need to check the filter of your furnace. A dirty filter can be the cause of your problem. If your filter is not clean, then you might start experiencing issues with your furnace because it tends to overheat most of the time when in use. That is why it is advisable that you check your filter before you check the other parts of your furnace. Solve this problem by cleaning your filter or by replacing it with a new one.

2 Reset The Device.

After changing the filter of your furnace or after cleaning it, try to reset the equipment by turning on the reset button. If the furnace fails to work, wait for approximately thirty minutes and try again. Pressing the reset button can help fix other issues that the gas furnace may be facing.

3 Check Door Cover.

You also need to check the door cover and make sure that it is closed correctly. If the door cover is not correctly installed, then your furnace will not start. Therefore, it is advisable that you check the door cover after changing the filter to ensure that it is installed properly.

4 Avoid Closing Lots Of Registers

Closing of too many registers can lead to high resistance and also an unnecessary buildup of heat in the furnace. Be sure not to close more than twenty percent for registers to avoid heat buildup. However, even though closing of some registers can help you save energy cost, it is advisableEcobuilt provides Furnace Repair in Kalamazoo Michigan - ecobuilthvac.com that you do not exceed 20%.

5 Verify That The Furnace Is Switched On.

Before you make a conclusion that your furnace is not working, first check the switch button and ensure that it is on when testing your product. That is because the furnace may not be damaged at all and the only reason as to why the problem persists is because it is not turned on.

6 Check The Condition Of Each Of The Fuses And Circuit Breakers.

Furnaces are not designed the same. Some have a separate entrance for power, which is usually located or installed in the different panel. Furthermore, other furnaces happen to have multiple fuses all mounted in the same unit. If you are unsure about doing this and wish to contact a furnace repair contractor in Kalamazoo Michigan you can visit our directory.

7 Examine the Thermostat To Ensure That It Is Turned On.

Thermostat select switch gives you the privilege of raising the temperature and lowering the temperature at the same time. However, it is advisable that you set your thermostat at room temperature if you want your furnace to work properly. Moreover, you also need to check the gas supply and make sure that it is turned on when using a gas furnace.

8 Make certain that the furnace venting is not blocked by ice.

If the furnace venting is blocked, then you need to find a way to unblock it if you want it to work properly.

9 Ensure That The Blower Fan Is Turned On

Some furnaces are designed with switch button for turning the blower on and off. Make sure the furnace blower fan is turned on when using this equipment.

The Way To Turn On A Gas Furnace

Ecobuilt Furnace Repair in Kalamazoo Michigan - ecobuilthvac.com

Turning on a gas furnace might seem like an easy thing, but it is not. Most people do not know how to do this, but with the help of this guide, you can start your furnace and turn it off when necessary.

1 The first thing you are required to do is to identify the breaker of the furnace. This is part of the electoral panel and is usually located in the basement or the utility room. The Breaker should be easy to find because most brands label their breaker with a furnace sticker.

2 After locating the breaker, press the switch button to turn on the furnace. However, you can only do this by identifying where the furnace switch is placed. Furnace switch can be placed in the basement or even in the ceiling. Sometimes it can be placed in the same room with the furnace to make it easy to find.

3 Set up the Thermostat. After turning on the furnace, make sure that it is set to heat by checking the selector switch. After making sure that the selector switch is properly set to heat, you can adjust the set point to acquire the temperature you want.



Ecobuilt HVAC | Building Contractors



Kalamazoo Furnace Repair Installer

Mo-Fr 08:00-17:30
Ecobuilt Logo
(855) 336-1607


Joshua Fletcher